The 5045E, 5055E, 5065E, and 5075E Utility Tractors meet U.S. Environmental Protection Agency (EPA) Final Tier 4 (FT4) exhaust emissions regulations with a diesel oxidation catalyst (DOC)/diesel particulate filter (DPF) system. Modifying the after-treatment device resulted in better forward and side visibility around the hood. The hood slope of the updated design is comparable to the Tier 2 tractors previously produced. Similar to the system on the 5M, the purpose of the DOC/DPF combination is to reduce toxic gases emitted from the exhaust, as well as to filter particulate matter to prevent it from becoming airborne.
As the tractor continues to operate over time, as is the case with any filter, the DPF will accumulate particulate matter and will need to be cleaned. It is cleaned through a process called regeneration. During a regeneration cycle, exhaust temperatures increase to burn off the excess particulate matter. On a John Deere 5 Series Tractor equipped with a DOC/DPF, the operator does not need to provide any input to trigger the regeneration process.
On the dash is an exhaust filter cleaning switch. As long as this switch remains in the auto position, the tractor is in full control of the regeneration process and will regenerate on an as-needed basis during operation. The operator just continues to operate the tractor as normal while the regeneration process takes place.
There may be times a tractor is operating in an environment not suitable for a regeneration cycle, such as in a confined area or during service. For this reason, the bottom section of the exhaust filter cleaning switch can be depressed to disable the regeneration. The disable position allows the operator to temporarily inhibit the regeneration cycle. The operator should return the switch to auto mode as soon as possible to avoid continued soot buildup in the exhaust filter, which can lead to a parked regeneration. John Deere does not recommend disabling the automatic exhaust filter cleaning unless it is absolutely necessary.
The simplicity and intuitiveness of the exhaust filter cleaning switch maximizes uptime by minimizing the operator’s input into the regeneration process. This increases the overall productivity of the tractor by reducing the chances of a parked regeneration. The operator-friendly interface allows the operator to easily complete the task at hand, even during the regeneration process.
Operator comfort is important regardless of the application. Improving the 5E 3-Cylinder Tractor models, the hand throttle has been relocated to the right-hand console. This is 30.5 cm (12-in.) closer to the operator and within easy reach versus the previous location on the center-hand console. Operators may also notice the additional legroom provided by the repositioned loader controls, providing a more enjoyable experience.
The SyncShuttle transmission is designed to match the excellent power and torque characteristics of the John Deere PowerTech™ engines. Transmission durability is enhanced with the pressure-lubricated top shaft, allowing an operator to achieve performance from one working season to the next. Additionally, this in-base transmission is configured with fixed draft links, single-speed power take-off (PTO) and mechanical PTO engagement.
The transmission is characterized as full top shaft synchronized (TSS) when forward shifting on-the-go between speeds, and is characterized a synchronized while depressing the clutch.
Nine forward and three reverse (9F/3R) speeds are achieved by using two platform-mounted levers for shift operation. The gear lever at the operator's right hand selects one of three forward gears and one reverse gear, as well as the integrated park position. The range lever at the operator's left hand selects collar-shift A, B, and C ranges.
Operators can easily switch directions without having to completely stop the tractor with synchronized, in-line, shuttle-shift capability between forward and reverse gears on the gear-shift lever in all three ranges (A, B, and C ranges).
A neutral start switch requires the gear-shift lever be in the neutral or park positions to start the engine.
A positive park pawl on the transmission provides positive park and eliminates the need for a hand brake. This also eliminates clutch service costs that occur when the park brake is accidentally left engaged.
Limited-slip, heavy-duty MFWD front axle will provide operators with increased drawbar pull and improved traction when operating in slippery conditions. This ensures the operator gets the required torque to the ground for applications that demand more from the tractor. The MFWD front axle also reduces wheel slippage with less tractor ballasting for reduced soil compaction, increased fuel economy, and longer tire life.
The MFWD centerline design provides excellent maneuverability around the worksite and more crop clearance so producers aren't driving down their crop or profits. Additional versatility is proven when wheel treads are adjusted with 6 degrees of caster angle and a 55-degree turn angle, which results in a turning radius as short as 3 m (9.9 ft) (brakes applied), allowing plenty of horsepower to turn around in tight places. 10 degrees of axle oscillation follows uneven terrain, allowing for consistent performance and comfortable ride.
Axle oscillation also reduces the stress and maintenance cost on the axle spindles because loads are consistently spread across the entire axle. The centerline design eliminates the need for drive shaft universal joints that require regular maintenance. Anti-wrap shielding on the driveline is standard to prevent crop material and debris from building around the driveline and ensures tractor performance. Three grease points are conveniently located to minimize maintenance time while maximizing front axle performance.
NOTE: The MFWD engagement lever is located on the left-hand side of the operator's seat. For the operator’s convenience, when MFWD is engaged, an indicator light will appear on the dash.
Specs & Compare
|Select up to 4 models to compare specifications|
|Description||John Deere PowerTech 3029|
|Cylinders liners||Wet sleeved|
|After treatment type|
|Displacement||3 cylinders: 2.9 L|
179 cu in.
|Rated power||At 2100 rpm: 37.2 kW|
|Rated PTO power (hp SAE)||At 2100 rpm: 27.5 kW|
37 PTO hp
|Power boost (available in transport and/or mobile PTO applications)|
|Engine peak torque|
|PTO torque rise|
|Type||Standard: 9F/3R SyncShuttle|
|Pump rated output||Standard: 68.9 L/min|
|Available flow at a single rear SCV||43.1 L/min|
|Available flow at front SCVs|
|Number of rear selective controls valves (SCVs)|
|Number of mid selective controls valves (SCVs)|
|Number of front selective controls valves (SCVs)|
|Joystick SCV control||2WD: FIK|
|Hitch draft control load sense type||Mechanical|
|Remote control valves available||Standard: 1|
|Hitch category (SAE designation)||Category 2; convertible to 1|
|Maximum lift capacity behind lift points|
|Sensing type||Top link|
|Rear axle differential lock|
|Maximum vertical load|
|Type||Standard: Independent 540|
|Engine rpm (at rated PTO speeds)||540 at 2100 rpm|
|PTO actuation||Mechanical (lever)|
|Standard lift capacity|
|Front power take-off (PTO)|
|Final drive type||Planetary|
|Differential controls||Mechanical (pedal)|
|Brakes, type and control||Hydraulic wet disc|
|Rear differential lock|
|Front axle differential lock|
|Front||2WD: 7.5-16 R1|
MFWD: 9.5-24 R1
|Rear||2WD: 13.6-28 R1|
MFWD: 13.6-28 R1
|Wheel tread range|
|Turning radius with brakes||2WD: 3.1 m|
MFWD: 2.94 m
|Turning radius without brakes||2WD: 2.94 m|
MFWD: 3.63 m
|Total cold cranking amps|
|Rollover protective structure, OOS||Rigid - foldable - telescopic|
Foldable, 2-postPlatform - flat/straddle
StraddleGearshift location - console/floor
Floor, on the side
|Inner cab volume|
|Cab glass area|
|Wheelbase||2WD and MFWD: 2050 mm|
|Front axle center|
|Approximate shipping weight, Open;Cab||MFWD: 2450 kg|
|Base machine weight|
|Maximum ballast level|
|Maximum permissible weight|
|Crankcase oil volume|
|Fuel tank||Standard: 68 L|
18 U.S. gal.
|Diesel exhaust fluid (DEF) tank|
|Interval for engine oil change|
|Interval for hydraulic/transmission oil change|
|Interval for engine coolant change|
|Lift capacity at full height|
|Maximum lift height|
|Country of manufacture||Pune, India|
¹Offer valid on qualifying purchases made between 01 May 2020 to 04 August 2020. Subject to approved installment credit with John Deere Financial. No down payment required. $16.67 per month for every $1,000 financed. 0% APR for 60 months only. Taxes, freight, setup and delivery charges could increase monthly payment. Sales made to government agencies, company direct sales or other businesses/agencies that participate in John Deere's Special Discount Program or in John Deere's Rental Business Program are not eligible. Available at participating U.S. dealers. Prices and models may vary by dealer. Offer available on new equipment and in the U.S. only. Prices and savings in U.S. dollars.
²Offer valid on qualifying purchases made between 01 May 2020 to 04 August 2020. Subject to approved installment credit with John Deere Financial. No down payment required. $14.68 per month for every $1,000 financed. 1.90% APR for 72 months only. Taxes, freight, setup and delivery charges could increase monthly payment. Sales made to government agencies, company direct sales or other businesses/agencies that participate in John Deere's Special Discount Program or in John Deere's Rental Business Program are not eligible. Available at participating U.S. dealers. Prices and models may vary by dealer. Offer available on new equipment and in the U.S. only. Prices and savings in U.S. dollars.
³Offer valid on qualifying purchases made between 01 May 2020 to 04 August 2020 and is subject to approval by John Deere Financial. 1.90% APR lease rate for exempt states only for up to 36 months operating lease or lease purchase. Taxes, freight, setup and delivery charges could increase monthly payment. Payments may vary based upon the end of lease term purchase option price and length of lease term. Not available for consumer use. Available at participating U.S. dealers. Prices and models may vary by dealer. Offer available on new equipment and in the U.S. only. Prices and savings in U.S. dollars.
⁴Offer available on qualifying purchases made between 01 May 2020 to 04 August 2020. Prices and models may vary by dealer. Save $2,250 on 5045E only. This can only be combined with the regular installment options. Sales made to government agencies, company direct sales or other businesses/agencies that participate in John Deere's Special Discount Program or Rental Business Program are not eligible. Some restrictions apply. See participating dealer for details and other financing options. Offer is available only at participating United States dealers. Prices and savings are in U.S. dollars.
¹Offer valid on qualifying purchases made between 01 May 2020 to 04 August 2020. Subject to approved installment credit with John Deere Financial. Down payment may be required. Average down payment is 20%. $179 monthly payment based on Sales Price of $18,701 with $3,740 down payment or trade-in, 84 months at 0% APR. Attachments, taxes, freight, setup and delivery charges could increase monthly payment. Available at participating U.S. dealers. Prices and models may vary by dealer. Offer available on new equipment and in the U.S. only. Prices and savings in U.S. dollars.