H310 LOADER

General Purpose (GP) buckets

• Compatible with digging teeth and replaceable cutting edge
• Not compatible with grapples
• The GP buckets are durable with full length side cutting edges, additional bottom skid plates, and a double reinforced top section
• Holes are drilled in the cutting edge allowing easy attaching of a reversible and replaceable cutting edge

Materials bucket

Materials buckets may be used for loading dirt, gravel, feed, and light materials as well as scraping, digging, and other general-purpose tasks.

NOTE: Materials buckets are not compatible with replaceable cutting edges or digging teeth.

This general-purpose bucket can be used in numerous applications.

The high-volume bucket is intended for use with lighter-density high-volume materials. The bucket capacity makes this an effective tool for handling snow, wood shavings, and other loose materials.

Materials bucket

Materials buckets may be used for loading dirt, gravel, feed, and light materials as well as scraping, digging, and other general-purpose tasks.

NOTE: Materials buckets are not compatible with replaceable cutting edges or digging teeth.

Replaceable wear edge

For those who frequently scrape on concrete, a replaceable cutting edge will greatly extend the life of the bucket:

• 1850-mm (73-in.) width replaceable cutting edge
• 2150-mm (85-in.) width replaceable cutting edge
• 2450-mm (96-in.) width replaceable cutting edge
• 2750-mm (108-in.) width replaceable cutting edge

Digging teeth can be added to the heavy-duty bucket for easier digging in hard ground or for breaking loose hard-packed materials such as manure or silage. Digging teeth are not compatible with replaceable cutting edges.

Stationary fender (H480 shown)

Loader stationary fenders are highly recommended for those operating in conditions where the front axle will be in full oscillation and turn frequently or where tight turns are made while maneuvering through gates or obstacles that will catch tractor axle-mounted fenders.

The loader stationary fenders still provide coverage for debris from the tire, but they do not protrude to become damaged in operation. The fenders can be removed to enable better access for servicing as well.

Five-tine round bale/silage grapple with grille

All compatible John Deere Loaders use the same five-tine, pin-on grapple. The advantages of this grapple are:

• The pin-on method puts the least amount of stress possible on the bucket.
• The grapple has a wide stance, making it more difficult to twist.

High-performance operators will choose the five-tine grapple for its increased durability and load-carrying capacity. Advantages include:

• The ability to handle two large round bales instead of one (where loader capacity allows).
• Strong grapple arms allow the bucket capacity to be increased by almost twice the amount of normal bucket capacity in materials such as silage.

The grapple is equipped with twin cylinders to provide excellent clamping force. 

NOTE: The center tine of the five-tine grapple is slightly off center to avoid contact with the placement of optional digging teeth.

NOTE: The grapple is not compatible with materials or high-volume buckets.

1850-mm (73-in.) bale grapple bucket

73–in. (1850 mm) grapple bucket BW15358 shown (all one piece

The bale grapple bucket is a complete solution ideal for full loads of silage, handling bales, or cleaning up debris or manure.

Two function

Two function quick coupler

The H240, H260, H310, H340, and H360 Loaders feature two-function quick-couplers in base machine. To disconnect the hydraulic connection between the loader and the tractor, it is necessary to relieve the hydraulic system oil pressure on the tractor.

To watch a video of how to use quick couplers click here.

NOTE: this video is intended to show the functionality of quick couplers only. Location of the connection varies across different loaders. 

Three function

Three function quick coupler

The H240, H260, H310, H340, and H360 Loaders can be equipped with three-function quick-couplers. Hoses will be installed in the boom arm and just the couplers will need to be assembled along with the third-function bracket and oil line. To disconnect the hydraulic connection between the loader and the tractor, it is necessary to relieve the hydraulic system oil pressure on the tractor.

The hood guard's basic function is to:

• Help protect the tractor grill and hood from falling debris or stationary objects such as a wagon or mixer while loading
• Allow for lighting at night

Compatibility:

• Can be used with or without the tractor front weight bracket but not with the actual front weights while using the loader (this would over load the front axle)
• Cannot be used with a front hitch

It is highly recommended to purchase a front weight bracket when using a loader. The hood guard is designed to be slightly rearward of the front weight bracket. This is so that the front weight bracket is the first point of contact against lower stationary objects.

Hood guard for 5E Interim Tier 4 (IT4) 4-Cylinder Tractors

The hood guard's basic function is to:

• Help protect the tractor grille and hood from falling debris or stationary objects, such as a wagon or mixer, while loading
• Allow for lighting at night
• Can be used with or without the tractor front weight bracket but not with the actual front weights while using the loader
• Cannot be used with a front hitch

It is highly recommended to purchase a front weight bracket when using a loader. The hood guard is designed to be slightly rearward of the front weight. This is so that the front weight is the first point of contact against lower stationary objects. 

Hood guard for 5M Series Tractors

Hood guard for 6D Series Tractors

The heavy-duty hood guard is compatible with 5M (5065M, 5075M, 5085M, 5095M, 5100M, 5105M, and 5115M), 6D – model year 2012 and prior (6100D, 6115D, 6130D, and 6140D), 6D – Interim Tier 4 (IT4) model years 2013 -2015 (6105D, 6115D, 6130D, and 6140D), and 6E Final Tier 4 (FT4) model year 2016 (6105E, 6120E, and 6135E) Tractors.

The basic function of a hood guard is to:

• Help protect the tractor grille and hood from falling debris or stationary objects such as a wagon or mixer
• Allow for lighting at night

The hood guard:

• Can be used with or without the tractor front weight bracket but not with the actual front weights while using the loader (this would overload the front axle)
• For the 5M Series Tractors, the bottom bar must be removed for usage with front hitch for storage position of the center link.

It is highly recommended to purchase a front weight bracket when using a loader. The hood guard is designed to be slightly rearward of the front weight bracket. This is so the front weight bracket is the first point of contact against lower stationary objects.

If a front weight bracket is not used, the lower bar can be moved downward to improve the protection of the grille below the lights.

The features of the hood guard include:

• Folds down to allow the hood to open and provide access to the battery and filter
• Extra steel behind the mainframe to increase strength
• High height to better protect the top of the hood

Hood guard on 6R Tractor

Hood guard for 6R folded down

The hood guard's basic function is to:

• Help protect the tractor grille and hood from falling debris or stationary objects such as a wagon or mixer
• Allow for lighting at night

Compatibility:

• Can be used with or without the tractor front weight bracket but not with the actual front weights while using the loader (this would overload the front axle)
• Cannot be used with a front hitch

It is highly recommended to purchase a front weight bracket when using a loader. The hood guard is designed to be slightly rearward of the front weight bracket. This is so the front weight bracket is the first point of contact against lower stationary objects. The height of the hood guard allows better protection for the top of the hood and allows operators to see the top of the hood guard.

Single-point hydraulic connection on row crop tractor

Single-point hydraulic connection on 5E Series Tractor

Single-point hydraulic connection on 5M Series Tractor

Single-point hydraulic connection with rigid lines on FT4 6R large frame

The H240, H260, H310, H340, and H360 Loaders feature a single-point hydraulic connection that also incorporates the connection point for any electrical needs as well. To disconnect the hydraulic connection between the loader and the tractor, it is necessary to relieve the hydraulic system oil pressure on the tractor.

To view a video of removing the single point hydraulic connection, click here.

Nitrogen-charged accumulator and electric valve

Operator on/off switch

LSS on H180

LSS on 5E and 5M

An enhancement to the loader is the suspension system. A great level of loader productivity is achieved with the LSS.

• An accumulator charged with nitrogen and connected to the head-end lift cylinder hose through a T-fitting provides shock absorption
• The cylinders move in and out to allow the boom to float 

Performance

• Bales can be transported more efficiently from one end of the field to the other over frozen, hard-packed, or rutted terrain.

NOTE: Check bale-handling capability of tractor before use.

• Pallets can be moved easily without sustaining cargo damage
• Pallets of seed or fertilizer can be carried across a yard without a bag spilling and creating a costly mess
• A properly-ballasted tractor with LSS has increased stability, creating a smoother ride for the operator

Cost of ownership

• Extended life of loader pins and bushings
• Less stress on tractor axle

Reasons for turning LSS off include:

• Digging applications - with LSS on, the cylinders retract slightly, losing lifting power
• Holding a grade when blading - with LSS on, it is difficult to hold a constant grade
• Precise pallet and bale handling - with LSS on, the load moves up and down slightly while being positioned
• Parking a loader - with LSS on, when down pressure is applied, the lift cylinders retract slightly, making it more difficult to park

The switch is conveniently located in the operator station to avoid having to exit the tractor seat to manually move the handle on the LSS.

LSS can also be ordered with a manual shutoff. Depending on the tractor/loader model, the accumulator is located in different places. On the 440R, the accumulator is mounted outside the bottom of the mounting frame. On the 5 Series Tractors, the accumulator is mounted near the inside of the rear right wheel. On 6 Series tractors and larger, it is mounted in between the hydraulic connection and the mounting frame.

Stationary fender (H480 shown)

Loader stationary fenders are highly recommended for those operating in conditions where the front axle will be in full oscillation and turn frequently or where tight turns are made while maneuvering through gates or obstacles that will catch tractor axle-mounted fenders.

The loader stationary fenders still provide coverage for debris from the tire, but they do not protrude to become damaged in operation. The fenders can be removed to enable better access for servicing as well.

Nitrogen-charged accumulator and electric valve

Operator on/off switch

LSS on H180

LSS on 5E and 5M

An enhancement to the loader is the suspension system. A great level of loader productivity is achieved with the LSS.

• An accumulator charged with nitrogen and connected to the head-end lift cylinder hose through a T-fitting provides shock absorption
• The cylinders move in and out to allow the boom to float 

Performance

• Bales can be transported more efficiently from one end of the field to the other over frozen, hard-packed, or rutted terrain.

NOTE: Check bale-handling capability of tractor before use.

• Pallets can be moved easily without sustaining cargo damage
• Pallets of seed or fertilizer can be carried across a yard without a bag spilling and creating a costly mess
• A properly-ballasted tractor with LSS has increased stability, creating a smoother ride for the operator

Cost of ownership

• Extended life of loader pins and bushings
• Less stress on tractor axle

Reasons for turning LSS off include:

• Digging applications - with LSS on, the cylinders retract slightly, losing lifting power
• Holding a grade when blading - with LSS on, it is difficult to hold a constant grade
• Precise pallet and bale handling - with LSS on, the load moves up and down slightly while being positioned
• Parking a loader - with LSS on, when down pressure is applied, the lift cylinders retract slightly, making it more difficult to park

The switch is conveniently located in the operator station to avoid having to exit the tractor seat to manually move the handle on the LSS.

LSS can also be ordered with a manual shutoff. Depending on the tractor/loader model, the accumulator is located in different places. On the 440R, the accumulator is mounted outside the bottom of the mounting frame. On the 5 Series Tractors, the accumulator is mounted near the inside of the rear right wheel. On 6 Series tractors and larger, it is mounted in between the hydraulic connection and the mounting frame.

Nitrogen-charged accumulator and electric valve

Operator on/off switch

LSS on H180

LSS on 5E and 5M

An enhancement to the loader is the suspension system. A great level of loader productivity is achieved with the LSS.

• An accumulator charged with nitrogen and connected to the head-end lift cylinder hose through a T-fitting provides shock absorption
• The cylinders move in and out to allow the boom to float 

Performance

• Bales can be transported more efficiently from one end of the field to the other over frozen, hard-packed, or rutted terrain.

NOTE: Check bale-handling capability of tractor before use.

• Pallets can be moved easily without sustaining cargo damage
• Pallets of seed or fertilizer can be carried across a yard without a bag spilling and creating a costly mess
• A properly-ballasted tractor with LSS has increased stability, creating a smoother ride for the operator

Cost of ownership

• Extended life of loader pins and bushings
• Less stress on tractor axle

Reasons for turning LSS off include:

• Digging applications - with LSS on, the cylinders retract slightly, losing lifting power
• Holding a grade when blading - with LSS on, it is difficult to hold a constant grade
• Precise pallet and bale handling - with LSS on, the load moves up and down slightly while being positioned
• Parking a loader - with LSS on, when down pressure is applied, the lift cylinders retract slightly, making it more difficult to park

The switch is conveniently located in the operator station to avoid having to exit the tractor seat to manually move the handle on the LSS.

LSS can also be ordered with a manual shutoff. Depending on the tractor/loader model, the accumulator is located in different places. On the 440R, the accumulator is mounted outside the bottom of the mounting frame. On the 5 Series Tractors, the accumulator is mounted near the inside of the rear right wheel. On 6 Series tractors and larger, it is mounted in between the hydraulic connection and the mounting frame.

Nitrogen-charged accumulator and electric valve

Operator on/off switch

LSS on H180

LSS on 5E and 5M

An enhancement to the loader is the suspension system. A great level of loader productivity is achieved with the LSS.

• An accumulator charged with nitrogen and connected to the head-end lift cylinder hose through a T-fitting provides shock absorption
• The cylinders move in and out to allow the boom to float 

Performance

• Bales can be transported more efficiently from one end of the field to the other over frozen, hard-packed, or rutted terrain.

NOTE: Check bale-handling capability of tractor before use.

• Pallets can be moved easily without sustaining cargo damage
• Pallets of seed or fertilizer can be carried across a yard without a bag spilling and creating a costly mess
• A properly-ballasted tractor with LSS has increased stability, creating a smoother ride for the operator

Cost of ownership

• Extended life of loader pins and bushings
• Less stress on tractor axle

Reasons for turning LSS off include:

• Digging applications - with LSS on, the cylinders retract slightly, losing lifting power
• Holding a grade when blading - with LSS on, it is difficult to hold a constant grade
• Precise pallet and bale handling - with LSS on, the load moves up and down slightly while being positioned
• Parking a loader - with LSS on, when down pressure is applied, the lift cylinders retract slightly, making it more difficult to park

The switch is conveniently located in the operator station to avoid having to exit the tractor seat to manually move the handle on the LSS.

LSS can also be ordered with a manual shutoff. Depending on the tractor/loader model, the accumulator is located in different places. On the 440R, the accumulator is mounted outside the bottom of the mounting frame. On the 5 Series Tractors, the accumulator is mounted near the inside of the rear right wheel. On 6 Series tractors and larger, it is mounted in between the hydraulic connection and the mounting frame.

Nitrogen-charged accumulator and electric valve

Operator on/off switch

LSS on H180

LSS on 5E and 5M

An enhancement to the loader is the suspension system. A great level of loader productivity is achieved with the LSS.

• An accumulator charged with nitrogen and connected to the head-end lift cylinder hose through a T-fitting provides shock absorption
• The cylinders move in and out to allow the boom to float 

Performance

• Bales can be transported more efficiently from one end of the field to the other over frozen, hard-packed, or rutted terrain.

NOTE: Check bale-handling capability of tractor before use.

• Pallets can be moved easily without sustaining cargo damage
• Pallets of seed or fertilizer can be carried across a yard without a bag spilling and creating a costly mess
• A properly-ballasted tractor with LSS has increased stability, creating a smoother ride for the operator

Cost of ownership

• Extended life of loader pins and bushings
• Less stress on tractor axle

Reasons for turning LSS off include:

• Digging applications - with LSS on, the cylinders retract slightly, losing lifting power
• Holding a grade when blading - with LSS on, it is difficult to hold a constant grade
• Precise pallet and bale handling - with LSS on, the load moves up and down slightly while being positioned
• Parking a loader - with LSS on, when down pressure is applied, the lift cylinders retract slightly, making it more difficult to park

The switch is conveniently located in the operator station to avoid having to exit the tractor seat to manually move the handle on the LSS.

LSS can also be ordered with a manual shutoff. Depending on the tractor/loader model, the accumulator is located in different places. On the 440R, the accumulator is mounted outside the bottom of the mounting frame. On the 5 Series Tractors, the accumulator is mounted near the inside of the rear right wheel. On 6 Series tractors and larger, it is mounted in between the hydraulic connection and the mounting frame.

Nitrogen-charged accumulator and electric valve

Operator on/off switch

LSS on H180

LSS on 5E and 5M

An enhancement to the loader is the suspension system. A great level of loader productivity is achieved with the LSS.

• An accumulator charged with nitrogen and connected to the head-end lift cylinder hose through a T-fitting provides shock absorption
• The cylinders move in and out to allow the boom to float 

Performance

• Bales can be transported more efficiently from one end of the field to the other over frozen, hard-packed, or rutted terrain.

NOTE: Check bale-handling capability of tractor before use.

• Pallets can be moved easily without sustaining cargo damage
• Pallets of seed or fertilizer can be carried across a yard without a bag spilling and creating a costly mess
• A properly-ballasted tractor with LSS has increased stability, creating a smoother ride for the operator

Cost of ownership

• Extended life of loader pins and bushings
• Less stress on tractor axle

Reasons for turning LSS off include:

• Digging applications - with LSS on, the cylinders retract slightly, losing lifting power
• Holding a grade when blading - with LSS on, it is difficult to hold a constant grade
• Precise pallet and bale handling - with LSS on, the load moves up and down slightly while being positioned
• Parking a loader - with LSS on, when down pressure is applied, the lift cylinders retract slightly, making it more difficult to park

The switch is conveniently located in the operator station to avoid having to exit the tractor seat to manually move the handle on the LSS.

LSS can also be ordered with a manual shutoff. Depending on the tractor/loader model, the accumulator is located in different places. On the 440R, the accumulator is mounted outside the bottom of the mounting frame. On the 5 Series Tractors, the accumulator is mounted near the inside of the rear right wheel. On 6 Series tractors and larger, it is mounted in between the hydraulic connection and the mounting frame.

The loader hoses are connected to the mid-tractor selective control valves (SCVs).

Two function

Two function quick coupler

The H240, H260, H310, H340, and H360 Loaders feature two-function quick-couplers in base machine. To disconnect the hydraulic connection between the loader and the tractor, it is necessary to relieve the hydraulic system oil pressure on the tractor.

To watch a video of how to use quick couplers click here.

NOTE: this video is intended to show the functionality of quick couplers only. Location of the connection varies across different loaders. 

Three function

Three function quick coupler

The H240, H260, H310, H340, and H360 Loaders can be equipped with three-function quick-couplers. Hoses will be installed in the boom arm and just the couplers will need to be assembled along with the third-function bracket and oil line. To disconnect the hydraulic connection between the loader and the tractor, it is necessary to relieve the hydraulic system oil pressure on the tractor.

The loader hoses are connected to the mid-tractor selective control valves (SCVs).

The loader hoses are connected to the mid-tractor selective control valves (SCVs).

Single-point hydraulic connection on row crop tractor

Single-point hydraulic connection on 5E Series Tractor

Single-point hydraulic connection on 5M Series Tractor

Single-point hydraulic connection with rigid lines on FT4 6R large frame

The H240, H260, H310, H340, and H360 Loaders feature a single-point hydraulic connection that also incorporates the connection point for any electrical needs as well. To disconnect the hydraulic connection between the loader and the tractor, it is necessary to relieve the hydraulic system oil pressure on the tractor.

To view a video of removing the single point hydraulic connection, click here.

The loader hoses are connected to the mid-tractor selective control valves (SCVs).

The loader hoses are connected to the mid-tractor selective control valves (SCVs).

Single-point hydraulic connection on row crop tractor

Single-point hydraulic connection on 5E Series Tractor

Single-point hydraulic connection on 5M Series Tractor

Single-point hydraulic connection with rigid lines on FT4 6R large frame

The H240, H260, H310, H340, and H360 Loaders feature a single-point hydraulic connection that also incorporates the connection point for any electrical needs as well. To disconnect the hydraulic connection between the loader and the tractor, it is necessary to relieve the hydraulic system oil pressure on the tractor.

To view a video of removing the single point hydraulic connection, click here.

Single-point hydraulic connection on row crop tractor

Single-point hydraulic connection on 5E Series Tractor

Single-point hydraulic connection on 5M Series Tractor

Single-point hydraulic connection with rigid lines on FT4 6R large frame

The H240, H260, H310, H340, and H360 Loaders feature a single-point hydraulic connection that also incorporates the connection point for any electrical needs as well. To disconnect the hydraulic connection between the loader and the tractor, it is necessary to relieve the hydraulic system oil pressure on the tractor.

To view a video of removing the single point hydraulic connection, click here.

Single-point hydraulic connection on row crop tractor

Single-point hydraulic connection on 5E Series Tractor

Single-point hydraulic connection on 5M Series Tractor

Single-point hydraulic connection with rigid lines on FT4 6R large frame

The H240, H260, H310, H340, and H360 Loaders feature a single-point hydraulic connection that also incorporates the connection point for any electrical needs as well. To disconnect the hydraulic connection between the loader and the tractor, it is necessary to relieve the hydraulic system oil pressure on the tractor.

To view a video of removing the single point hydraulic connection, click here.

Replaceable wear edge

For those who frequently scrape on concrete, a replaceable cutting edge will greatly extend the life of the bucket:

• 1850-mm (73-in.) width replaceable cutting edge
• 2150-mm (85-in.) width replaceable cutting edge
• 2450-mm (96-in.) width replaceable cutting edge
• 2750-mm (108-in.) width replaceable cutting edge

The loader hoses are connected to the mid-tractor selective control valves (SCVs).

The loader hoses are connected to the mid-tractor selective control valves (SCVs).

Two function

Two function quick coupler

The H240, H260, H310, H340, and H360 Loaders feature two-function quick-couplers in base machine. To disconnect the hydraulic connection between the loader and the tractor, it is necessary to relieve the hydraulic system oil pressure on the tractor.

To watch a video of how to use quick couplers click here.

NOTE: this video is intended to show the functionality of quick couplers only. Location of the connection varies across different loaders. 

Three function

Three function quick coupler

The H240, H260, H310, H340, and H360 Loaders can be equipped with three-function quick-couplers. Hoses will be installed in the boom arm and just the couplers will need to be assembled along with the third-function bracket and oil line. To disconnect the hydraulic connection between the loader and the tractor, it is necessary to relieve the hydraulic system oil pressure on the tractor.

The loader hoses are connected to the mid-tractor selective control valves (SCVs).

The loader hoses are connected to the mid-tractor selective control valves (SCVs).

The loader hoses are connected to the mid-tractor selective control valves (SCVs).

Single-point hydraulic connection on row crop tractor

Single-point hydraulic connection on 5E Series Tractor

Single-point hydraulic connection on 5M Series Tractor

Single-point hydraulic connection with rigid lines on FT4 6R large frame

The H240, H260, H310, H340, and H360 Loaders feature a single-point hydraulic connection that also incorporates the connection point for any electrical needs as well. To disconnect the hydraulic connection between the loader and the tractor, it is necessary to relieve the hydraulic system oil pressure on the tractor.

To view a video of removing the single point hydraulic connection, click here.

Hood guard on 6R Tractor

Hood guard for 6R folded down

 The hood guard's basic function is to:

• Help protect the tractor grille and hood from falling debris or stationary objects such as a wagon or mixer
• Allow for lighting at night

Compatibility:

• Can be used with or without the tractor front weight bracket but not with the actual front weights while using the loader (this would overload the front axle)
• Cannot be used with a front hitch

It is highly recommended to purchase a front weight bracket when using a loader. The hood guard is designed to be slightly rearward of the front weight bracket. This is so the front weight bracket is the first point of contact against lower stationary objects. The height of the hood guard allows better protection for the top of the hood and allows operators to see the top of the hood guard.

Hood guard for 5M Series Tractors

Hood guard for 6D Series Tractors

The heavy-duty hood guard is compatible with 5M (5065M, 5075M, 5085M, 5095M, 5100M, 5105M, and 5115M), 6D – model year 2012 and prior (6100D, 6115D, 6130D, and 6140D), 6D – Interim Tier 4 (IT4) model years 2013 -2015 (6105D, 6115D, 6130D, and 6140D), and 6E Final Tier 4 (FT4) model year 2016 (6105E, 6120E, and 6135E) Tractors.

The basic function of a hood guard is to:

• Help protect the tractor grille and hood from falling debris or stationary objects such as a wagon or mixer
• Allow for lighting at night

The hood guard:

• Can be used with or without the tractor front weight bracket but not with the actual front weights while using the loader (this would overload the front axle)
• For the 5M Series Tractors, the bottom bar must be removed for usage with front hitch for storage position of the center link.

It is highly recommended to purchase a front weight bracket when using a loader. The hood guard is designed to be slightly rearward of the front weight bracket. This is so the front weight bracket is the first point of contact against lower stationary objects.

If a front weight bracket is not used, the lower bar can be moved downward to improve the protection of the grille below the lights.

The features of the hood guard include:

• Folds down to allow the hood to open and provide access to the battery and filter
• Extra steel behind the mainframe to increase strength
• High height to better protect the top of the hood

The loader hoses are connected to the mid-tractor selective control valves (SCVs).

The loader hoses are connected to the mid-tractor selective control valves (SCVs).

5M mounting frame

5M mounting frame

6E Final Tier 4 (FT4) and 6D Interim Tier 4 (IT4) (model year 2013-2015) mounting frame

6D (model year 2012 and prior) mounting frame

6M (small chassis), 6R (small chassis), 6030, 6030 Premium, 6020, 6010, and 6000 Series Tractors mounting frame

5E 4 Cylinder (IT4; 5085E, 5100E) mounting frame

Mounting frames are designed to evenly distribute forces during loader operation. Hardware is accessible to torque to the correct specifications.

5M mounting frame

5M mounting frame

6E Final Tier 4 (FT4) and 6D Interim Tier 4 (IT4) (model year 2013-2015) mounting frame

6D (model year 2012 and prior) mounting frame

6M (small chassis), 6R (small chassis), 6030, 6030 Premium, 6020, 6010, and 6000 Series Tractors mounting frame

5E 4 Cylinder (IT4; 5085E, 5100E) mounting frame

Mounting frames are designed to evenly distribute forces during loader operation. Hardware is accessible to torque to the correct specifications.

5M mounting frame

5M mounting frame

6E Final Tier 4 (FT4) and 6D Interim Tier 4 (IT4) (model year 2013-2015) mounting frame

6D (model year 2012 and prior) mounting frame

6M (small chassis), 6R (small chassis), 6030, 6030 Premium, 6020, 6010, and 6000 Series Tractors mounting frame

5E 4 Cylinder (IT4; 5085E, 5100E) mounting frame

Mounting frames are designed to evenly distribute forces during loader operation. Hardware is accessible to torque to the correct specifications.

5M mounting frame

5M mounting frame

6E Final Tier 4 (FT4) and 6D Interim Tier 4 (IT4) (model year 2013-2015) mounting frame

6D (model year 2012 and prior) mounting frame

6M (small chassis), 6R (small chassis), 6030, 6030 Premium, 6020, 6010, and 6000 Series Tractors mounting frame

5E 4 Cylinder (IT4; 5085E, 5100E) mounting frame

Mounting frames are designed to evenly distribute forces during loader operation. Hardware is accessible to torque to the correct specifications.